ZyXEL Communications Network Router NOT AVAILABLE Manuale Utente Pagina 63
- Pagina / 300
- Indice
- SEGNALIBRI
Valutato. / 5. Basato su recensioni clienti
Chapter 6 Interfaces
NXC CLI Reference Guide
63
The following table describes the commands available for VLAN interface management. You
must use the
configure terminal command to enter the configuration mode before you
can use these commands.
description Sets the description of the interface. You may use 0 - 511 alphanumeric
characters, underscores (
_), or dashes (-), but the first character cannot
be a number. This value is case-sensitive.
profile_name The DHCP pool name.
Table 21 Input Values for VLAN Interface Commands (continued)
LABEL DESCRIPTION
Table 22 Command Summary: VLAN Interface Profile
COMMAND DESCRIPTION
[no] interface virtual_interface Enters configuration mode for the specified interface. Use
the no command to remove the specified VLAN interface.
vlanid <1..4094> Sets the interface’s VLAN identification number.
[no] ip address ip_address netmask Sets the interface’s IP address and netmask address.
Use the no command to remove these values from this
interface.
[no] ip address dhcp [metric <0..15>] Sets the interface to use the DHCP to acquire an IP
address. Enter the metric (priority) of the gateway (if any)
on this interface. The NXC decides which gateway to use
based on this priority. The lower the number, the higher
the priority. If two or more gateways have the same
priority, the NXC uses the one that was configured first.
mtu <576..1500> Sets the maximum size of each data packet, in bytes, that
can move through this interface. If a larger packet arrives,
the NXC divides it into smaller fragments.
no mtu Disables the mtu feature for this interface.
[no] ip gateway gateway [metric
<0..15>]
Enter the IP address of the gateway. The NXC sends
packets to the gateway when it does not know how to
route the packet to its destination. The gateway should be
on the same network as the interface.
Also enter the metric (priority) of the gateway (if any) on
this interface. The NXC decides which gateway to use
based on this priority. The lower the number, the higher
the priority. If two or more gateways have the same
priority, the NXC uses the one that was configured first.
join <interface_name> <tag|untag> Links the VLAN to the specified physical interface and
also sets this interface to send packets with or without a
VLAN tag.
no join <interface_name> Disassociates the specified physical interface from the
VLAN.
upstream <0..1048576> Sets the maximum amount of traffic, in kilobits per
second, the NXC can send through the interface to the
network.
no upstream Disables the upstream bandwidth limit.
downstream <0..1048576> Sets the maximum amount of traffic, in kilobits per
second, the NXC can receive from the network through
the interface.
no downstream Disables the downstream bandwidth limit.
- NXC Series 1
- CLI Reference Guide 1
- IMPORTANT! 2
- Contents Overview 3
- Table of Contents 10
- NXC CLI Reference Guide 10
- Table of Contents 11
- Chapter 34 12
- Chapter 35 12
- CHAPTER 1 15
- 1.2.1 Console Port 16
- Figure 3 Console 17
- Table 2 Console 18
- LABEL DESCRIPTION 18
- 1.2.3 Telnet 20
- 1.2.4 SSH (Secure SHell) 20
- 1.4.1 Background Information 21
- 1.4.2 Command Input Values 21
- 1.5 CLI Modes 22
- 1.6 Shortcuts and Help 23
- 1.7 Input Values 26
- 1.9 Logging Out 29
- CHAPTER 2 31
- 2.1.1 Debug Commands 33
- CHAPTER 3 35
- Chapter 3 Object Reference 36
- CHAPTER 4 37
- RAM size, and serial number 38
- Chapter 4 Status 39
- Chapter 4 Status 40
- CHAPTER 5 41
- Chapter 5 Registration 42
- 5.2 Registration Commands 43
- 5.3 Country Code 44
- Chapter 5 Registration 45
- CHAPTER 6 49
- Chapter 6 Interfaces 52
- 6.2.2 DHCP Setting Commands 53
- Chapter 6 Interfaces 57
- 6.4 Port Commands 59
- 6.5 Port Role Commands 60
- CHAPTER 7 65
- Chapter 7 Route 68
- 7.3 IP Static Route 69
- 7.4 Static Route Commands 70
- Chapter 7 Route 71
- CHAPTER 8 73
- 8.2 AP Management Commands 74
- Chapter 8 AP Management 75
- Chapter 8 AP Management 76
- CHAPTER 9 77
- 9.3 SSID Profile Commands 83
- 9.3.1 SSID Profile Example 84
- CHAPTER 10 89
- Chapter 10 Rogue AP 90
- Chapter 10 Rogue AP 91
- Denial of Service attack 92
- CHAPTER 11 93
- CHAPTER 12 95
- 12.2.1 DCS Examples 96
- CHAPTER 13 99
- CHAPTER 14 103
- Chapter 14 Dynamic Guest 104
- Chapter 14 Dynamic Guest 105
- CHAPTER 15 107
- 15.2 Zone Commands Summary 108
- 15.2.1 Zone Command Examples 109
- Chapter 15 Zones 110
- CHAPTER 16 111
- 16.2 ALG Commands 112
- 16.3 ALG Commands Example 112
- CHAPTER 17 113
- Chapter 17 Captive Portal 114
- CHAPTER 18 117
- Chapter 18 RTLS 118
- CHAPTER 19 119
- 19.2 Firewall Commands 120
- Chapter 19 Firewall 121
- 19.2.1 Firewall Sub-Commands 122
- 19.3 Session Limit Commands 124
- means all IP 125
- means all users 125
- Chapter 19 Firewall 126
- CHAPTER 20 127
- 20.2.2.1 Rule Sub-commands 129
- Chapter 20 Application Patrol 130
- CHAPTER 21 137
- 21.2.3 White and Black Lists 140
- Chapter 21 Anti-Virus 141
- Chapter 21 Anti-Virus 142
- Table 76 Update Signatures 142
- 21.4 Anti-virus Statistics 143
- CHAPTER 22 145
- 22.3 IDP Profile Commands 146
- Chapter 22 IDP Commands 147
- old_profile new_profile 147
- Chapter 22 IDP Commands 148
- 22.3.6 Signature Search 153
- If you 155
- 22.4 IDP Custom Signatures 156
- fragoffset_rel: 159
- 22.5 Update IDP Signatures 160
- 22.6 IDP Statistics 161
- CHAPTER 23 163
- 23.1.1 Before You Begin 164
- Chapter 23 Device HA 165
- Chapter 23 Device HA 168
- CHAPTER 24 169
- 24.2.1 User Commands 170
- 24.2.2 User Group Commands 171
- 24.2.3 User Setting Commands 171
- 24.2.4 MAC Auth Commands 173
- Chapter 24 User/Group 174
- Chapter 24 User/Group 175
- CHAPTER 25 177
- Chapter 25 Addresses 180
- CHAPTER 26 181
- ICMP_ECHO to SG1 183
- Chapter 26 Services 184
- CHAPTER 27 185
- Chapter 27 Schedules 186
- Table 109 schedule Commands 186
- CHAPTER 28 187
- Chapter 28 AAA Server 192
- CHAPTER 29 193
- 29.3 test aaa Command 195
- CHAPTER 30 197
- CHAPTER 31 199
- Chapter 31 ENC 201
- Chapter 31 ENC 202
- CHAPTER 32 203
- Chapter 32 Certificates 205
- Chapter 32 Certificates 206
- CHAPTER 33 207
- Chapter 33 System 208
- 33.3 Host Name Commands 209
- 33.4 Time and Date 209
- 33.4.1 Date/Time Commands 210
- 33.5 Console Port Speed 211
- 33.6 DNS Overview 211
- 33.6.2 DNS Command Example 212
- CHAPTER 34 213
- 34.3 HTTP/HTTPS Commands 214
- 34.4 SSH 216
- 34.5 Telnet 217
- 34.6 Telnet Commands 218
- 34.7 Configuring FTP 219
- 34.8 SNMP 220
- 34.8.3 SNMP Commands 221
- 34.9 Language Commands 222
- CHAPTER 35 223
- Chapter 35 File Manager 224
- Chapter 35 File Manager 225
- 35.6 FTP File Transfer 228
- Figure 23 Firmware Damaged 232
- Figure 24 Enter Debug Mode 232
- Figure 34 Restart Complete 236
- Figure 38 Enter Debug Mode 238
- Figure 44 Startup Complete 240
- CHAPTER 36 241
- 36.1.1 Log Entries Commands 242
- 36.1.2 System Log Commands 242
- 36.1.3 Debug Log Commands 243
- Chapter 36 Logs 247
- Chapter 36 Logs 248
- CHAPTER 37 249
- 37.1.3 Session Commands 250
- Chapter 37 Reports and Reboot 252
- 37.3 Reboot 254
- CHAPTER 38 255
- Chapter 38 Session Timeout 256
- CHAPTER 39 257
- Chapter 39 Diagnostics 258
- CHAPTER 40 259
- CHAPTER 41 261
- Chapter 41 Maintenance Tools 262
- 41.1.1 Command Examples 263
- Chapter 41 Maintenance Tools 265
- CHAPTER 42 267
- 42.3 Application Watchdog 268
- Chapter 42 Watchdog Timer 269
- Chapter 42 Watchdog Timer 270
- CHAPTER 43 271
- 43.3 CAPWAP Client Commands 272
- 43.4 DNS Server Commands 274
- List of Commands 277
- List of Commands 279
Prodotti e manuali riguardandi Software ZyXEL Communications Network Router NOT AVAILABLE
Software ZyXEL NSA210 Manuale Utente
(576 pagine)
(576 pagine)
Software ZyXEL IES-5005 Manuale Utente
(100 pagine)
(100 pagine)
Tripp Lite IS500 manuels
Manuels d'utilisation et guides de l'utilisateur pour Accessoires pour ordinateurs Tripp Lite IS500.
Nous fournissons des manuels en pdf 1 Tripp Lite IS500 à télécharger gratuitement par type de document : Manuel de l'utilisateur
Commenti su questo manuale